I used a pair of pliers to gently squeeze the plastic nuts and push them out from the inside of the old battery cover towards the outside. There are a lot of pieces to this set and it took me probably 2 hours to take the car apart and fit them all on, but when it was done they looked great. For more information please call us toll free at 1-800-663-7750. After evaluating the options, I decided to order a replacement battery from Toyota and swap it myself. Some may have harness anchors bolted on the floor of the interior, on the outside edge of the seat.
At least this was the case with my 2000 Montana, and I would imagine it is also the case with similar models. Therefore, it can be removed, if only for battery maintenance. You mentioned that it's been resolved in other thread. In this case, the project vehicle is a 2003 Toyota Camry, but the process is similar for other Toyota vehicles as well. Sep 13, 2010 The trunk release cable runs along the inside edge of the car, under the carpet, on the driver side.
Put a screwdriver under the rear seat cushion and pull up on it to undo the fasteners that release the sea The rear bumper of your 2001 Toyota Camry plays an important role in your vehicle's safety, because it provides a buffer between you and the impact created were another vehicle to run into the back of you. You will need to remove the rear seat bottonm and the seat back, and pull the carpet back on the driver's side to see the cable. I have removed knuckle assembly and pressed out bearing hub assembly, I have the new bearing hub assembly. The dealer quoted a turbo and to pull the charge air cooler and clean. Putting parts on the new battery Second vent tube about to be reinstalled. Make sure the gaskets are snug against the window or replace them.
I'm trying to remove the throttle body on my 2002 Echo. The two other screws will slide out of the plastic cap with a little force. You have to remove some 12mm and 10mm nuts, plus one T30 Torx screw, to remove the cover. I peeled back the tape on the end of the battery, and removed the rubber grommet through the steel end plate by squeezing and pulling. When the car is turned off, the steering wheel never locks.
You will notice a clicking sound when it has come loose. These are not actually screwed in. I suspect, but don't know, that this plug is used at the factory and maybe at the warehouses to check on the overall battery voltage and possibly to recharge it, using a very well-regulated charger with overcurrent, overvoltage, and timed shutoffs. Twist the exposed wire to prevent it from fraying, and then insert it into one side of the butt connector. I then carefully pulled the wires and thermistor towards the interior of the battery.
The inside of the cover. The far end of the battery, with the second bus bar module protector removed. Difficulty:Moderately EasyInstructions Pull up on the front corner of the seat until you hear a popping sound. Once the manifold is removed, I could squeeze in on the rubber lip at the end of the vent tube, and pull it out of the steel end plate of the battery. Then just reverse steps to re-install. Replace the rest of the removed components -- door panel s , seat s , door jamb kick-plate s -- that were required to remove the seatbelt assembly.
The car has been very good to me I believe that's due to steadfast preventative maintenance. On the ground, next to the car. Starting to come out the door. There are two twist locks to open it. There is a small 12 volt battery used for powering up the computer and powering the 12 volt accessories in the car. We got a certified used 370Z about 4-5 months ago from a Nissan dealership. I used these two holes only, ending up with one extra screw.
The containers can also be locally recycled into fiberglass insulation. The reason I'm telling you this is because our 5th gen Celica had backup light trouble and after all was said and done, we found … out it was the switch. I left the seat belt for the center rear seat passenger installed and just put it around the driver's headrest to keep it out of the way. After removing the cover, you will see the lock holded by two nuts. I was having problems with my 2010 Prius, when I would try to put gas in it the pump would cut off after a small amount of gas.
Again, this is the retaining clip popping out of the foot pan. If you fail to get them in the right spot, you'll be off a tooth, and that would suck performance-wise. The lifespan of the high voltage battery varies. Note that it is held to the case with three screws. Also am wondering how hard is it to keep the moonstone cloth or softex clean. View of passenger end of battery.