I believe it is against federal law to reset the odometer. To install a bulb, align the tabs of the bulb socket with the cutouts of the mounting hole. Determine which headlight s is not working. I actually removed my battery on my Camry. Aiming is not necessary after replacing the bulb. I am sure they can give you some… Good Question, I have to replace my headlight as well. My Wife noticed it was blown this morning.
Hi: My best bet is to remove the plastic container sitting behind the head light. Depress the end… You have to carefully remove the rubber protection from the bulb holder. There are 2 bolts inside of the box compartment, they are under a felt. Replace it and set back this black cover and that's it but if you… Depending on wether you talking about the light bulb retainer of the head light assembly to include the lens you probably need to remove the air filter box on one side and possibly the battery on the other. The bulb on the drivers side is difficult to get to, the one on the passenger side is easily accessible for removal and practice before you try the drivers side.
Test new light operation with key in ignition switch and in the on… All you have to do is lift or take off the black part where the shift lock release button cover is also located. Also, make sure its headlights are switched off. Putting it back together is just as easy. If it's stubborn gently slide a stiff, thin piece under the sides and pull the housing up and toward you. Don't brake or damage it because you will have to put it back. However I have rust to clear out so I don't want the glass in and…. You can draw a diagram before you remove it.
Any damage to your headlight lens assembly can be dangerous on the road. Turn off the car and headlights. . Pulling on one of the tabs on the large hockey-puck sized rubber seal that surrounds the connector and lamp, stretch the seal slitghtly so it can release from the groove that holds it in place. Just pull the housing back toward you.
Purchase a replacement bulb s. To change the headlight bulb, all you need to do is reach around behind the headlight and detach the light from the plug. Same for the other trip meter. It is located… The bulb is accessable from the interior of the vehicle. Remove the black plastic trim around the shift.
Do this after you remove the wire connection from the back of… Step1 Shut off the Camry's engine and set the parking brake for added safety. You can use your fingers tips by inserting them around the inside cut out of the trim, rear side, lift the trim. You can xerox copies of what you need to know, if they won't let you 'check it out'. Step5 Unplug the electrical connector from the back of… You can click on the information on the right and it will take you through each procedure. You can reach both the high… 1. Turn the plastice device to unlock it and pull back. A damaged or failing lens can result in limited visibility at night and make driving unsafe.
Remove a screw that holds the front part of the console at the drivers side. The connector may have a locking tab, which has to be depressed. There is a collar that you have to twist about a quarter turn to remove. That should help you out a lot. What you have to do is to open the hood of your Toyota and dependant upon which side of the car the bulb is being replaced look behind the headlight. Add some waterproof grease if required. If I get out of the car through the passenger door rather than the drivers door; typically because I'm parked too close to something on the drivers door the lights stay on continuously.
After that you have to unlock the locking bracket by just pushing it out of the groove. Remove the headlamp connector by a straight pull, rocking if necessary. After that just replace the bulb. Press on the lock tab on the wire connector, and pull the bulb off of the connector. Install the new bulb and install the connector.
We are a company of car enthusiasts for car enthusiasts and we are passionate about helping you enhance the look feel and handling of your 2002 Toyota Camry. Open the trunk, theres a plastic cover over the light assembly, with 3 plastic screws that turn a quarter turn then pop up, pull then out, pry the cover off, find the back of the bulb housing. You do not need any tools and you should not have to remove anything else to do this. Twist counterclockwise and remove the grey plastic bulb holder. Look inside the hood directly behind the headlight that does not work.