Eaton fuller autoshift code 88. freightliner century auto stuck in gear 2019-02-22

eaton fuller autoshift code 88

Heavy Duty Transmission, Constant Mesh and Synchronized Manual Transmissions,

eaton fuller autoshift code 88

Do not remove the Electric Shifter at any time. The braid shall be heat-sealed to prevent unraveling. The Drive Coupler alignment tool must be used when installing the Drive Coupler. Note: For tools contact Deutsch at 951-765-2250. I could not for the life of me get this truck to act up. Input Shaft To Clutch Alignment: The transmission is shipped from Eaton with the transmission in gear. Now for fun if you go by the code 8 8 N F.

Next

Auto

eaton fuller autoshift code 88

Cadence of the tone is controlled by Gen 3. The countershaft journal can be. It then shows N and then flashes F. Start the engine and rev it above 1500 rpm. Make sure shifter is in neutral.

Next

Eaton 10 speed autoshift , indicator says F

eaton fuller autoshift code 88

Annunciator shall adhere to the following requirements. Verify the transmission diagnostic connector is accessible 10. Install the Input shaft pilot bearing. These mechanics that think they are doing you a favor replacing or patching that one little spot aren't. Source Address 41 shall be used anytime valid data is received from both addresses. Remove the eight 8 mounting bolts from the Adapter Plate. Note: Failure to perform this step will set a clutch disengagement fault and inhibit transmission gear engagement.

Next

PLEASE HELP

eaton fuller autoshift code 88

For example: If you have a 4 degree transmission mounting angle, then 8 degrees or 14 percent of grade is equal to the limit of 12 degrees. J1939 Cable 12 Hercules Dr. Cab Floor Access Plate - A cab floor access plate is necessary for access and removal of components from the transmission top. Possible sources for oil contamination are wear particles generated due to normal transmission wear as well as any foreign objects introduced into the transmission during transport or installation. Tighten mounting bolts to 40-45 lbs. See Lubricant Requirement section in this manual for details. Transmission Component Temperature Requirements - The temperature limit for all electrical and air system components is 250F° 121°C.

Next

Auto

eaton fuller autoshift code 88

Make sure oil is within dipstick marks. If the elevated temperature is associated with an unusual operating condition that will recur, a cooler should be added, or the capacity of the existing cooling system increased. The face of the engine flywheel housing and the face of the transmission clutch housing must be parallel during installation. A copy of the checklist should be recorded for installation history. I had a driver in the truck who ended up getting arrested for some dumb mess he decided to do while parked at a walmart and then walmart had the truck and trailer towed while he was in jail. With Engine not running, select drive and attempt to start the engine.

Next

Eaton Ultra Shift on Volvo, Pete, & KW

eaton fuller autoshift code 88

Thre are way too many. The ground connection must be isolated from local power device ground returns. This may have to be done several times before the transmission learns. I have a 05 387 with a 10 speed eaton auto shift tranny sometime feels like it goes in and out of gear indicator light blinks like a miss sometimes acts up then may go 200 miles perfectly just pulled it out of shop no codes replaced spend sensor clutch is good so is 9 and 10th gears only acts up it 10th put it in 9th works fine anyone have this problem don't want to throw parts at it only thing is harness or ecm just want to be sure before I change them Be glad they replaced the entire harness. Do yourself a favor and make sure you have eatons manual handy, even mechanics at volvo dealer have to go through same procedure listed on road rangers pdf file on line.

Next

Heavy Duty Transmission, Constant Mesh and Synchronized Manual Transmissions,

eaton fuller autoshift code 88

Gen 3 requires an informational tone that consists of a single tone and an alert tone that is continuous until conditions change that prompted the alert. Remove and discard the Adapter Plate and gasket from the transmission. Working on auto-shift transmissions requires extensive troubleshooting procedures before the mechanic begins changing parts, and we often see some new parts on auto-shifts that have made it to our shop after the regular mechanic gives up. Stripping An allowable maximum of one strand may be cut on 16 gauge or larger, no strands on 18 gauge, and no strands on 20 gauge in the crimp area. These transmissions are bad about the yoke nut loosening and it will throw a code for output shaft speed sensor data eratic, when the yoke gets loose it will fracture the sensor and throw theis code causing othe codes to appear also and it will hang up in whatever gear it's in at the time, even when you replace the sensor it will throw the code because of the vibration.

Next

Auto

eaton fuller autoshift code 88

Verify that it is engaged before bolting the clutch to the engine. The lock plate, bracket, and two screws, that hold the range valve in place, are replaced by two screws with conical washers. Verify lubricant type and brand label affixed to transmission fill plug 12. Caution: Failure to follow indicated procedures may cause component damage or malfunction. Actual oil level must be within Eaton specifications according to the dipstick readings.

Next